Mina is intended for use as an anti-handling devices for anti-personnel mines that do not have their own such a device.
Furthermore, the mine may be used as a booby trap discharge action.
When used as an anti-handling device Mine mine ML-7 is installed underneath a landmine push action PMN, PMN-2, PMD-6m, or similar, and if you try to remove antipersonnel mines from the site is a mine explosion ML-7, which affects deminers opponent. Thus there and knock, or the destruction of anti-personnel mines.
When used as a booby-trap ML-7 is installed on the ground so that it could not be seen (such as in an open well), but it fits the subject, which is sure to arouse the interest of the enemy and induce him to pick up or use them (weapons, items life, etc.). In this case, the defeat of the personnel of the force applied by the explosion (high-explosive effect).
Mina consists of a housing (1), the explosive charge (2) and two additional detonator (3).
Housing mines rectangular plastic and is used to place the fuse, discharge target sensor (spring-loaded lid), two additional charge of explosives and detonators.
Explosive charge consists of two plastic boxes filled with explosives type PVV-5. These boxes are mounted on the sides of the body spring clips and can optionally be removed from the mines.
Additional detonators are placed in the body on both sides of the fuse and are tetrilovye checkers to 5 gr. weight each, and are used to transmit the detonation of the fuse to the explosive charge.
Safety fuse type unloading activities and consists of the following systems - the system of protection, long-cocking mechanism, protecting and detonating the device and ispolnitelny mechanism.
Safety system is designed to ensure the safe handling of the mine for transport and transfer of the fuze into the firing position.
Long-cocking mechanism allows bringing the fuse in the firing position after 45 seconds. - 20 min. after the safety pin is removed the system of protection.
Slam-detonating device makes it impossible to mine explosion in transport position and at the same time reliable transmission of detonation fuse detonators through additional to the charge of explosives in a combat situation.
The actuator provides the fuze action when removed from the mine load.
The picture shows the mine at the outset clearly visible two boxes with an explosive charge, target sensor (push cap), the ring of safety checks and red ribbon pins push the lid.
Mina can only be installed manually on the surface or in the ground, snow. To use underwater mine is not.
The term combat operation mines is not defined. Mine is not equipped with a self-killer. Mina and neobezvrezhivaemaya unrecoverable.
Mina has a fuse, which is part of the design mines.
The performance characteristics of mines ML-7Type of mine ................................................ ............ Blast trap discharge actionWeight mines ................................................ ......... 100 gr.Weight of explosive charge (PVV-5 + tetryl) ........................ 40 gr. (30 oz. - RWA-5, 10 gr. - Tetryl)Length ................................................. ................. 7.2 cmWidth ................................................. ............... 6.9 cmHeight ................................................. ................ 3 cmMinimum weight of the load ................................. 300 gr.Type of target sensor ............................................... ... mechanical unloadingDimensions of the sensor target ........................................... 5.5 x 5.5 cmThe transfer to the firing position ..................... 45 sec. temp. +50 g.
20 min temp. -40 G.Temperature range .................... -40 - +50 DegreesType of long-cocking mechanism ....................... hydromechanicalFuse ................................................. .......... own mechanicalObezvrezhivaemost ............................................... neobezvrezhivaemayaRecoverability ................................................. ...... UnrecoverableSelf-neutralization / self-destruction ...................... No / NoThe term combat operations ............................................... not determinedGuaranteed shelf life .................................... 10 yearsThe combination of mine / objects ............................. anti-push action / any weight more than 0.3 kg.Restrictions on the power grid and el.navodkam ........... noDetectability ................................................. . Metal Detectors - less than 4 cm,
radochastotnye detectors - less than 5 cm,
odorantnye detectors - 25-40 cmTime and payment for the installation of mines ........................... 4 min. 1 person.
Installing mine is safe enough. Since pulling combat checks and studs mines to cover the moment of the fuse cocked depending on the ambient temperature goes from 45 sec. (At +40 deg.) To 20 minutes (at -40 deg.).
When all the tasks of bringing anti-personnel mines in the firing position of the ML-7 pin removed the lid and check the combat, followed by masking min. Since the pull-out checks from ML-7 reverse translation her to a safe position possible. When the time delay ML-7 is sure to become cocked. If at this point on it will not load, the ML-7 explode.
The minimum weight of the load shall be not less than 300 gr .. ML-7 explosion occurs, the displacement of cargo up to 3-5 mm.
The mines are packed in boxes for 72-ta (gross weight of 24 kg.) Is not completely kitted out. Box size 65.8h59.8h20.6sm. Additional detonators are stored in the same box separately min.
Color grayish-blue min. Maybe olive, sand-yellow, yellowish-gray. Markings are applied mechanically (extruded) on the cover of mine and is a standard (shiftr mines, the code of the manufacturer, lot number and year of manufacture. Several parties have no markings min.
Mina was adopted by the Soviet Army in 1984 and is widely used in the war in Afghanistan (1979-89). During 1985-86. and during the two Chechen wars (1995-96, 1999-02). Quite significant quantities of these mines were in the former Soviet republics (Tajikistan, Kazakhstan, Kyrgyzstan, Turkmenistan, Ukraine, Belarus). It is therefore possible appearance of these mines in the regions of local conflicts.
The reason for adopting a min ML-7 was that by 1983, spooks began to remove significant amounts established by Soviet troops mines PMN and PMN-2 and actively use them in battles against Soviet forces. Use as anti-handling devices mines MS-3 was not possible due to the small weight of antipersonnel mines PMD-6m, PMN, PMN-2 and MS-4 mines were too expensive.
Installing the Soviet sappers mines with anti-handling devices homemade repeatedly led to accidents, as well as sharply increased time on mining, while low quality home-made anti-handling devices.
This all led to the emergence and ML-7 min, and they were used very little, about 1-2 thousand for a period of 9-11 months, 85-86. Then spooks almost universally abandoned the removal of Soviet anti-personnel mines and went back to the tried simple and efficient way to mine - run large flocks of sheep through suspicious areas.
Furthermore, the mine may be used as a booby trap discharge action.
When used as an anti-handling device Mine mine ML-7 is installed underneath a landmine push action PMN, PMN-2, PMD-6m, or similar, and if you try to remove antipersonnel mines from the site is a mine explosion ML-7, which affects deminers opponent. Thus there and knock, or the destruction of anti-personnel mines.
When used as a booby-trap ML-7 is installed on the ground so that it could not be seen (such as in an open well), but it fits the subject, which is sure to arouse the interest of the enemy and induce him to pick up or use them (weapons, items life, etc.). In this case, the defeat of the personnel of the force applied by the explosion (high-explosive effect).
Mina consists of a housing (1), the explosive charge (2) and two additional detonator (3).
Housing mines rectangular plastic and is used to place the fuse, discharge target sensor (spring-loaded lid), two additional charge of explosives and detonators.
Explosive charge consists of two plastic boxes filled with explosives type PVV-5. These boxes are mounted on the sides of the body spring clips and can optionally be removed from the mines.
Additional detonators are placed in the body on both sides of the fuse and are tetrilovye checkers to 5 gr. weight each, and are used to transmit the detonation of the fuse to the explosive charge.
Safety fuse type unloading activities and consists of the following systems - the system of protection, long-cocking mechanism, protecting and detonating the device and ispolnitelny mechanism.
Safety system is designed to ensure the safe handling of the mine for transport and transfer of the fuze into the firing position.
Long-cocking mechanism allows bringing the fuse in the firing position after 45 seconds. - 20 min. after the safety pin is removed the system of protection.
Slam-detonating device makes it impossible to mine explosion in transport position and at the same time reliable transmission of detonation fuse detonators through additional to the charge of explosives in a combat situation.
The actuator provides the fuze action when removed from the mine load.
The picture shows the mine at the outset clearly visible two boxes with an explosive charge, target sensor (push cap), the ring of safety checks and red ribbon pins push the lid.
Mina can only be installed manually on the surface or in the ground, snow. To use underwater mine is not.
The term combat operation mines is not defined. Mine is not equipped with a self-killer. Mina and neobezvrezhivaemaya unrecoverable.
Mina has a fuse, which is part of the design mines.
The performance characteristics of mines ML-7Type of mine ................................................ ............ Blast trap discharge actionWeight mines ................................................ ......... 100 gr.Weight of explosive charge (PVV-5 + tetryl) ........................ 40 gr. (30 oz. - RWA-5, 10 gr. - Tetryl)Length ................................................. ................. 7.2 cmWidth ................................................. ............... 6.9 cmHeight ................................................. ................ 3 cmMinimum weight of the load ................................. 300 gr.Type of target sensor ............................................... ... mechanical unloadingDimensions of the sensor target ........................................... 5.5 x 5.5 cmThe transfer to the firing position ..................... 45 sec. temp. +50 g.
20 min temp. -40 G.Temperature range .................... -40 - +50 DegreesType of long-cocking mechanism ....................... hydromechanicalFuse ................................................. .......... own mechanicalObezvrezhivaemost ............................................... neobezvrezhivaemayaRecoverability ................................................. ...... UnrecoverableSelf-neutralization / self-destruction ...................... No / NoThe term combat operations ............................................... not determinedGuaranteed shelf life .................................... 10 yearsThe combination of mine / objects ............................. anti-push action / any weight more than 0.3 kg.Restrictions on the power grid and el.navodkam ........... noDetectability ................................................. . Metal Detectors - less than 4 cm,
radochastotnye detectors - less than 5 cm,
odorantnye detectors - 25-40 cmTime and payment for the installation of mines ........................... 4 min. 1 person.
Installing mine is safe enough. Since pulling combat checks and studs mines to cover the moment of the fuse cocked depending on the ambient temperature goes from 45 sec. (At +40 deg.) To 20 minutes (at -40 deg.).
When all the tasks of bringing anti-personnel mines in the firing position of the ML-7 pin removed the lid and check the combat, followed by masking min. Since the pull-out checks from ML-7 reverse translation her to a safe position possible. When the time delay ML-7 is sure to become cocked. If at this point on it will not load, the ML-7 explode.
The minimum weight of the load shall be not less than 300 gr .. ML-7 explosion occurs, the displacement of cargo up to 3-5 mm.
The mines are packed in boxes for 72-ta (gross weight of 24 kg.) Is not completely kitted out. Box size 65.8h59.8h20.6sm. Additional detonators are stored in the same box separately min.
Color grayish-blue min. Maybe olive, sand-yellow, yellowish-gray. Markings are applied mechanically (extruded) on the cover of mine and is a standard (shiftr mines, the code of the manufacturer, lot number and year of manufacture. Several parties have no markings min.
Mina was adopted by the Soviet Army in 1984 and is widely used in the war in Afghanistan (1979-89). During 1985-86. and during the two Chechen wars (1995-96, 1999-02). Quite significant quantities of these mines were in the former Soviet republics (Tajikistan, Kazakhstan, Kyrgyzstan, Turkmenistan, Ukraine, Belarus). It is therefore possible appearance of these mines in the regions of local conflicts.
The reason for adopting a min ML-7 was that by 1983, spooks began to remove significant amounts established by Soviet troops mines PMN and PMN-2 and actively use them in battles against Soviet forces. Use as anti-handling devices mines MS-3 was not possible due to the small weight of antipersonnel mines PMD-6m, PMN, PMN-2 and MS-4 mines were too expensive.
Installing the Soviet sappers mines with anti-handling devices homemade repeatedly led to accidents, as well as sharply increased time on mining, while low quality home-made anti-handling devices.
This all led to the emergence and ML-7 min, and they were used very little, about 1-2 thousand for a period of 9-11 months, 85-86. Then spooks almost universally abandoned the removal of Soviet anti-personnel mines and went back to the tried simple and efficient way to mine - run large flocks of sheep through suspicious areas.
No comments:
Post a Comment